Power-vent vs atmospheric-vent water heaters
The vent, not the tank color, often decides which gas water heater can be installed in a given Minnesota basement. Official code and the manufacturer’s listing control that choice; this page does not invent efficiency claims.
Atmospheric (natural-draft) venting
An atmospheric, or natural-draft, gas storage water heater uses a draft hood and relies on the buoyancy of hot exhaust to rise through a vertical chimney or a properly lined flue. It typically draws combustion air from the room. In an older Twin Cities house with an existing tile-lined chimney that is still in good condition and correctly sized, that arrangement may still be appropriate. In a tight, remodeled, or long-horizontal-run situation, it may not be. Spillage of exhaust into the living space is a safety issue, not a performance footnote.
Power venting
A power-vent water heater uses a fan to push exhaust through a listed vent, which can often run horizontally to a sidewall termination when the manufacturer allows it. That can matter in a finished basement, a house whose chimney has been abandoned or is no longer lined for this appliance, or a location far from a vertical flue. Power-vent units still have clearance, termination, and combustion-air rules in the listing and in the Minnesota codes administered by the Department of Labor and Industry. Some designs are power-direct-vent or sealed-combustion units that draw air from outdoors; those are a distinct listing, not a nickname for every fan-assisted tank.
Condensing equipment and other side effects
Higher-efficiency condensing water heaters, including some power-vent and tankless models, produce condensate that must be drained according to the listing and the plumbing code. They are not a drop-in for every atmospheric tank. Electrical service is also required for the fan, and a gas line may need to be evaluated if the burner input changes. The cost drivers guide lists those items without invented prices.
What the Minnesota code pages actually cover
Minnesota has adopted a state plumbing code (Minnesota Rules chapter 4714) and related mechanical and fuel-gas provisions, with official materials at the Department of Labor and Industry. This page does not reprint vent tables. A licensed plumber and the city inspector, using the manufacturer’s installation manual and the adopted code, determine whether a given vent path is allowed. Several cities also require a plumbing permit to install or replace a water heater; see the city pages and rebates and permits.
Need a licensed plumber for the work?
You can request a quote from a licensed Twin Cities plumber. A licensed local plumber will follow up. This site is an independent reference guide and may be compensated for referrals.
Common questions
Can I vent a power-vent water heater out a sidewall?
Many power-vent units are listed for sidewall venting with a fan, subject to the manufacturer’s instructions and the Minnesota Plumbing and Fuel Gas / Mechanical codes as adopted. An atmospheric (gravity-vent) unit is generally tied to a vertical chimney or lined flue. A licensed plumber should confirm what the existing vent can legally and safely accept.
Is a power-vent unit always more efficient?
This page does not invent efficiency percentages. Some power-vent and condensing units are designed for higher efficiency than a basic atmospheric tank, but the listing, Uniform Energy Factor, and installation all matter. Check the specification sheet and any utility rebate model list.
Sources
- Conventional Storage Water Heaters — U.S. Department of Energy, Energy Saver. Accessed November 20, 2026.
- Water Heating — U.S. Department of Energy, Energy Saver. Accessed November 20, 2026.
- 2020 Minnesota Plumbing Code — Minnesota Department of Labor and Industry. Accessed November 19, 2026. Chapter 4714 took effect December 17, 2021. It incorporates the 2018 Uniform Plumbing Code with Minnesota amendments.
- Minnesota Rules 4714.0101, Conformance with Code — Minnesota Office of the Revisor of Statutes. Accessed November 19, 2026. The code applies to new plumbing installations statewide, including additions, extensions, alterations, and replacements.
- Minnesota Rules 4714.0504, Water Heater Requirements — Minnesota Office of the Revisor of Statutes. Accessed November 19, 2026. Covers temperature, pressure, and vacuum relief devices. A shutoff valve shall not be placed between the relief valve and the water heater or on discharge pipes between the valves and the atmosphere.